You can find the existing black box line and replace it with the same location and plug it in. It removed the fuse line in front of the red line power outlet and the yellow line sunroof, and I didn’t need the yellow line, so only the power outlet line was replaced.Straighten the wire again and put it into the left hole below and send it back to the center hole.After turning on the engine, you can select the default screen mode. It can come out half and half together with the front and the rear, or only the front or the rear can come out.Black box test screen for morning commuteThe new cable line has gone all the way to the rear, so connect it to the rear camera and test its operation. Formatting and re-operating the existing SD card works well.It rained on my way home from work in the evening. In the dark at night, the rear part is sometimes glaring due to the light, so you can adjust it according to the situation. When you press the lower button of the rear mirror, the screen turns off and becomes a rear mirror mirror. If you press it again, the screen appears and the reaction speed is fast, so it’s good.Attach the wire and rear camera cable lines to pierce and pull them out from the bottom. The rubber pipe is made for waterproofing and the pipe itself is bent, making it difficult to pass through.Most of the symptoms of Pineview T20R failure are said to be image sensor problems. Since I’ve been using it since 2016, I’ve been using it stably for quite a long time, but I think it’s time to go.According to the Internet, the same used model can be sent and replaced for about 40,000 won. Of course, it is a used product. The free warranty is about six months. Considering the cost of buying a new one and installing it, it wouldn’t be a bad idea to replace it like this, but I didn’t want to replace the 2015-2016 product with the same cost. Even if it is replaced, the image sensor will be able to go out again sometime.Installation Start ★ Preparations: Driver, spanner, remover, test machine, iron disposable hanger, tape To remove the existing black box, first remove the driver’s left handle by loosening the bolt.But oh… it’s a mistake. The mini USB is the same, but the existing Fine View cable DC jack does not fit inside the newly purchased DC jack. The appearance is 3.5mm, but it must have been smaller than 1.5mm inside. The more you try to make it comfortable, the more difficult it is, and the faster you go, the more you get sick. I have no choice but to remove the existing cable and install it on FM.The black box, which has been used well, has failed once. The rear seems to be working well, but the front recording was not done.Tap the passed rear cable on the left hanger (A) to pull the wire on the opposite hanger (B).I bought a guy with a good review for his cost-effectiveness through Ali. I bought it at a lower price than the repair cost because it would be nice to be able to see the real-time video delivered to the rear camera through the rear mirror. It can be purchased at about $32. I tested the product I received, and the video showed well without any problems. However, since the power connection jack is different from the one installed in the existing car, the desire to work comfortably is like a chimney, so I looked for a compatible jack that fits the existing Fine View cable and ordered it. This lazy simbo to work more and more comfortably.If you have removed the wires from the back, you will have to pass through the rubber pipe, which is expected to be the most difficult. If there are not many lines in the existing rubber pipe, this is also the most comfortable work if it passes by attaching and pulling to the existing rear camera line, but there are many lines in the rubber pipe due to work lines such as camping in the back, so it is really difficult to pass them in this way. I tried it, but it didn’t work, so I eventually use the method of opening the hanger wire that everyone uses and attaching it to it and passing it through.39.7US달러 57% 할인|거울 카메라 자동차 터치 스크린 비디오 레코더 후방 대시 캠 전방 후방 DVR – DVR/대시 카메라 – 알리익스프레스 스마트 쇼핑, 더 나은 생활! Aliexpress.coms.click.aliexpress.comBlack box test screen on a rainy dayOnce passed, it’s easy after that. Untying the tape you put on, you just have to remove the wire from the rubber pipe again. As shown in the picture below, it was very difficult for me to remove the other wires from the rubber pipe. Still, the material is rubber, so it stretches, so if you keep squeezing it in, you’ll get the result. Be careful not to tear the rubber pipe by using the tape to pass it through the pointed side of the wire.The black box structure looks mostly the same. I looked for ways to repair the broken black box and found that when the front camera with the camera was removed, the image sensor came out. There was a way to restore it by covering it with lead and removing it cleanly. I tried the second method, but it was determined that it could not be recovered.To remove the existing line, the fuse box and the left cover must be opened, but when the rubber packing is held first and lifted, it falls out. When lifting one side of the left cover, it opens the other side as well.You have to pull it out through the back hole like the bottom, but there is an existing line, so if you stick it like the top and pull it from behind, it becomes easier to work. Due to the annoyance, only the baby hairs stretch. No, this is also called a technique, not the baby hairs. There is no need to make it difficult to do something easy and fast.I did a black box test on my way to work. Overall good and very satisfying.It seems as if the bottle is turning again to make it easier… The line should be pulled out over the ceiling and sent back. If possible, instead of just removing the existing line, tape the new line to be installed on the existing line as shown below, and go to the back of the car and pull the existing line to easily pull out the new line behind the ceiling. If this is not done, the ceiling should be torn off or the line should be pulled back by using wire.감지된 언어가 없습니다.
입력 언어를 확인해 주세요.
